cisco 2504 controller web setting

command 改csico controller ip 

>wlan disable all 

>configure interface address managent IP-ADDRESS SUBNETMASK GATEWAY

>wlan enable all

show ap join stats summary all

show ap summary

在interface 編輯 DHCP server  

security>AAA>TACACS+>Local Net Users可以看建立哪些帳號

web認證  

security>Web Auth> Web Login Page> web authentication type(選internal)

management>Mgmt Via Wireless> Enable Controller ... Clients口 要打勾

這樣才能從底下AP連上來的client管理controller 

management>Local Management User >建立管理帳號

Lobbyadmin介紹:建立臨時帳號的管理者 

改Controller IP等資訊

Controller>Interfaces>Interface Name點進去

[Device] cisco controller setup final

Would you like to terminate autoinstall? [yes]:

System Name [Cisco_b8:71:c4] (31 characters max):
AUTO-INSTALL: process terminated -- no configuration loaded
2504
Enter Administrative User Name (24 characters max): cisco
Enter Administrative Password (3 to 24 characters): ********
Re-enter Administrative Password                 : ********

Enable Link Aggregation (LAG) [yes][NO]: no

Management Interface IP Address: 192.168.45.200
Management Interface Netmask: 255.255.255.0
Management Interface Default Router: 192.168.45.254
Management Interface VLAN Identifier (0 = untagged):
Management Interface Port Num [1 to 4]: 1
Management Interface DHCP Server IP Address: 172.16.41.1

Virtual Gateway IP Address: 1.1.1.1

Multicast IP Address: 239.0.0.1

Mobility/RF Group Name: poc

Network Name (SSID): poc

Configure DHCP Bridging Mode [yes][NO]:

Allow Static IP Addresses [YES][no]:

Configure a RADIUS Server now? [YES][no]: no
Warning! The default WLAN security policy requires a RADIUS server.
Please see documentation for more details.

Enter Country Code list (enter 'help' for a list of countries) [US]: TW

Enable 802.11b Network [YES][no]:
Enable 802.11a Network [YES][no]:
Enable 802.11g Network [YES][no]:
Enable Auto-RF [YES][no]:

Configure a NTP server now? [YES][no]:
Enter the NTP server's IP address: 211.22.103.158
Enter a polling interval between 3600 and 604800 secs: 3600

Configuration correct? If yes, system will save it and reset. [yes][NO]: yes

Configuration saved!
Resetting system with new configuration...


Configuration saved!
Resetting system with new configuration...
Restarting system.

cisco ap >> ERROR!!! Command is disabled.

喔我好強XD

1. 刪除現有的ios,讓他回復到最初機器上面的
2. clear pre-config


ERROR!!! Command is disabled.

出現這訊息,就不用在ap上踹了,直接到controller的web介面
找到這台ap的mac 或hostname, 直接在上面修改 hostname or ip等資訊
收工~

若硬要console設定ap 下文說是需要給ap一組username/password
我沒試過..因為上面做完就收工了.

Q. When I enable some LWAPP commands on my LAP, I get an error that says the command is disabled. Why is this?

 
AccessPoint#clear lwapp ap controller ip address 
ERROR!!! Command is disabled.

A. Once your AP has successfully joined a controller, the LWAPP commands are disabled. In order to enable LWAPP commands again, you must set the username/password of the AP from the controller CLI with the config ap username <name> password <pwd> <cisco-ap>/all command. Once that is done, you can do a clear lwapp private-config in the AP CLI to allow you to manually re-issue the AP LWAPP configuration commands.
Note: If you are running WLC version 5.0 and later, use this command to set the username and password on the AP:

config ap mgmtuser add username AP_username 
password AP_password secret secret {all | Cisco_AP}

cisco ap ERROR!!! Command is disabled.